myHanse.com - Hanse Yacht Owners Website myHanse.com - Hanse Yacht Owners Website myHanse.com - Hanse Yacht Owners Website myHanse.com - Hanse Yacht Owners Website

Welcome to myHanse.com the forum for Hanse Yachts owners throughout the world.

Forum Home Forum Home > Hints and Tips > 415/418
  New Posts New Posts RSS Feed - Me Genertion Anchor
  FAQ FAQ  Forum Search   Events   Register Register  Login Login

Me Genertion Anchor

 Post Reply Post Reply Page  <12
Author
Message
Mike2145 View Drop Down
Captain
Captain


Joined: 18 October 2014
Location: UK Hamble
Status: Offline
Points: 203
Post Options Post Options   Thanks (0) Thanks(0)   Quote Mike2145 Quote  Post ReplyReply Direct Link To This Post Posted: 27 February 2019 at 07:49
Originally posted by Rod Rod wrote:

Further to the above am on the way to the Aegean and on arrival planned to upgrade the 16kg Delta to a 25kg Vulcan, plus 60-70M of chain, In order to sleep easier! Looking at the Rocnor sizing chart it appears that 25kg would be the optimal weight as last week the boat weighed 11MT on the travel lift and we have yet to load out !. However downloaded the Vulcan template and it does not quite fit on the bow roller. Has anyone fitted a 25kg Spade, Ultra or Rocnor ? If so did you modify the bow roller etc.
Will the current windlass Fisherman Pro 1000 handle the weight of chain, 70 metres of 8mm  plus 25kg anchor?
 
Thanks
Rod
 
 

I have fitted a 25Kg Rocna. I had a new roller made that has a smaller diameter (38mm) that lowered the shank so that the anchor pin fitted. As the shank was a little longer than the ultra it replaced a small modification was required to the anchor locker lid. This was quite minor. 
Also the shank would foul the roller reefing gear as it deployed. I had a simple hoop made to protect it.
Iím not on the boat at the moment but Iíll try and get some photos next time Iím on board. 
Cant take a joke, don't buy a boat.
Back to Top
Ratbasher View Drop Down
Commander
Commander
Avatar

Joined: 31 May 2017
Location: UK
Status: Offline
Points: 118
Post Options Post Options   Thanks (0) Thanks(0)   Quote Ratbasher Quote  Post ReplyReply Direct Link To This Post Posted: 27 February 2019 at 15:33
Neil - can you please confirm if a short bowsprit would still clear the Rocna when fitted, please? Would very much like to fit the Rocna but I secure a top-down furler off the bowsprit.


Thanks!




H400 #311 'Wight Leopard', cruising UK & Ireland

Back to Top
cgabay View Drop Down
Sub Lieutenant
Sub Lieutenant
Avatar

Joined: 20 October 2017
Location: Turkey
Status: Offline
Points: 7
Post Options Post Options   Thanks (0) Thanks(0)   Quote cgabay Quote  Post ReplyReply Direct Link To This Post Posted: 28 February 2019 at 09:50
I fitted Ultra 21 with ultra flip swiwel. No change required on 418. It was straghtforward replacement.
Back to Top
Rod View Drop Down
Commander
Commander
Avatar

Joined: 11 March 2013
Location: Dubai
Status: Offline
Points: 114
Post Options Post Options   Thanks (0) Thanks(0)   Quote Rod Quote  Post ReplyReply Direct Link To This Post Posted: 01 March 2019 at 07:09
Thanks I looked at the Ultra 21 and there does not seem to be any indication of weight of the boat versus required size of anchor, whereas Rocna and others take the weight as well as length into account. Does your Ultra handle high winds shear etc with a fast reset ?
I am just trying to draw a template for a Spade to see if that fits on the original bow fitting. Reasons for Vulcan versus original Rocna are to be able to use Code zero and other sails off the bow sprit - which will foul the roll bar. Another downside of the Vulcan is that it can not be pinned onto the roller at sea . So its back to the drawing board .
Hanse 415 - "Ti"
Sail Nbr "UAE 415"
Dubai Offshore Sailing Club
Back to Top
Rock View Drop Down
Captain
Captain


Joined: 19 September 2014
Location: Netherlands
Status: Online
Points: 219
Post Options Post Options   Thanks (0) Thanks(0)   Quote Rock Quote  Post ReplyReply Direct Link To This Post Posted: 14 May 2020 at 17:10
 Guys,

I asked Iain, in another thread, for a picture of a Rocna on the H400 bowroller.
Just realized silverlining already posted one.

There are discussions about the Rocna messing with the gennaker on the short/std. bowsprit.

Does any of you have good experience, can you fly the gennaker of the short bowspirit with a Rocna on the roller?

Best regards,
Peter 
Hanse 400e "M-square2" #0241
Back to Top
Muriel View Drop Down
Lieutenant Commander
Lieutenant Commander


Joined: 19 February 2019
Location: Pittwater Aust.
Status: Offline
Points: 50
Post Options Post Options   Thanks (0) Thanks(0)   Quote Muriel Quote  Post ReplyReply Direct Link To This Post Posted: 14 May 2020 at 21:08
And to add in another consideration, we fitted a Sarca Excel No 5 at 22kg to our 418.  Fitted like a glove and very happy.
Cheers
Bruce J
If you don't know where you are going, how will you know when you get there?

Cheers
Bruce J

Muriel 418 #081
Back to Top
StavrosNZ View Drop Down
Commadore
Commadore


Joined: 24 October 2014
Location: New Zealand
Status: Offline
Points: 382
Post Options Post Options   Thanks (0) Thanks(0)   Quote StavrosNZ Quote  Post ReplyReply Direct Link To This Post Posted: 14 May 2020 at 21:39
I have also fitted Ultra 21kg and Ultra swivel on my 400, prior to that had a 20kg Rocna. The Ultra anchor is a great fit and plenty of anchor for a 40" boat.

I use single snubber in light winds but move to a double snubber bridle in a blow 14mm nylon from each forward deck cleat to take all of the load and no load on bow roller at all.


Edited by StavrosNZ - 22 May 2020 at 03:48
Stephen
2010 H400 #691, Auckland, New Zealand
Back to Top
 Post Reply Post Reply Page  <12
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 12.01
Copyright ©2001-2018 Web Wiz Ltd.

This page was generated in 0.063 seconds.

Links : www.hanseyachts.co.uk www.hanseyachts.com www.fjordboats.co.uk www.dehler.co.uk www.varianta.co.uk